Nano traffic paint

Nickel traffic paint made by E-color Company is a single component paint consisting of nanoparticles that has special chemical and physical properties. This paint, which is part of very new achievements, is the best alternative to save money and prevent the loss of financial and human resources due to the very high consumption of paints and traffic covers. Since the basic specifications and method of using it are quite similar to other traffic colors, so it can be easily replaced in traffic systems.

Description of nano traffic color

Its properties include:

Very smooth, even and impermeable surface
Very good brightness and effect
Good abrasion resistance
Water and moisture resistant
Excellent resistance to ultraviolet radiation of the sun
Oils resistant to fuels
Very fast drying speed
has very good self-cleaning capability
Excellent adhesion to asphalt and concrete
Excellent adhesion and durability
Can be used and executed with marking machines
Usability in different climatic zones
Can be used with glass bits

Uses

This color is widely used for marking and marking roads and passages, including its uses are:

Roads and highways
Airport runway markings
Urban thoroughfares
Urban bookmarks
Marking halls and parking lots
Painting floors and walls of halls and parking lots

Technical specifications

فام td>	Traffic white – Traffic yellow – Other shades
Volume solid percentage	58 ± 2
Storage time	one year
Recommended thickness	100 to 400 microns
Density	05, 0 ± 1.25
350 micron theory coverage	1.2 square meters per kilogram

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
25 ° C	1 hour	10 hours	2 days	6 hours	7 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Traffic thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	5-10%	3-5%	3-7%	4-8%
head pressure	2 -5 times	140 – 160 bar
Nozzle head diameter	1.2 to 1.8 mm	0.3 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree (SP10-SSPC). In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.

Staining instructions

After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform. Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.

Storage and transportation

The above color was flammable Therefore, it should be sealed in a sealed container and kept away from moisture, fire, and strong currents of electricity and incendiary materials. It is recommended to consume the contents of the container as soon as possible after opening the lid. Suitable storage temperature is 20 degrees Celsius.

Safety

When applying paint, use safety equipment such as masks, goggles, robes and proper ventilation. In case of contact with skin, clean the area with a cloth soaked in a suitable condition and wash with plenty of lukewarm water and soap. Avoid breathing paint vapors, especially during application.

محصولات مشابه

عنوان

لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.