Iron oxide alkyd primer SSPC-PAINT25 (Type2)
Alkaline iron oxide primer E-color contains anti-corrosion pigment iron oxide. Its drying is the result of solvent jumping and oxidation.
Description of nano traffic color
Its properties include:
- Very smooth, even and impermeable surface
- Very good brightness and effect
- Good abrasion resistance
- Water and moisture resistant
- Excellent resistance to ultraviolet radiation of the sun
- Oils resistant to fuels
- Very fast drying speed
- has very good self-cleaning capability
- Excellent adhesion to asphalt and concrete
- Excellent adhesion and durability
- Can be used and executed with marking machines
- Usability in different climatic zones
- Can be used with glass bits
Uses
This color is widely used for marking and marking roads and passages, including its uses are:
- Roads and highways
- Airport runway markings
- Urban thoroughfares
- Urban bookmarks
- Marking halls and parking lots
- Painting floors and walls of halls and parking lots
Technical specifications
| فام | Traffic white – Traffic yellow – Other shades |
| Volume solid percentage | 58 ± 2 |
| Storage time | one year |
| Recommended thickness | 100 to 400 microns |
| Density | 05, 0 ± 1.25 |
| 350 micron theory coverage | 1.2 square meters per kilogram |
Drying and coating conditions
| Drying time | Next layer application time | ||||||
| Temperature | surface | depth | Complete hardening | minimum | Maximum | Notes | |
| 25 ° C | 1 hour | 10 hours | 2 days | 6 hours | 7 days | Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time. | |
Terms and equipment of application
| Thinner | Traffic thinner |
| Application temperature | 5 to 50 degrees Celsius |
| Maximum relative humidity | 80% |
| Surface temperature | 3 to 5 degrees above the dew point |
| Application method | Air spray. Airless spray, brush and roll |
| Application conditions | Ordinary spray | Airless spray | brush | Roll |
| Percent solvent | 5-10% | 3-5% | 3-7% | 4-8% |
| head pressure | 2 -5 times | 140 – 160 bar | ||
| Nozzle head diameter | 1.2 to 1.8 mm | 0.3 to 0.5 mm | ||
| hand distance | 30-50 cm | 40-60 cm |
Surface preparation
Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect
Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create
Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree
(SP10-SSPC).
In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness.
After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.
Staining instructions
After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform.
Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.
Storage and transportation
The above color was flammable
Description of iron oxide alkyd primer SSPC-PAINT25 (Type2)
Its properties include:
- Good flexibility
- Create a smooth and even surface
- Excellent adhesion to metal surfaces
- Easy to run
- Good corrosion resistance
Uses
This primer is used to protect steel structures against corrosive agents in marine or industrial environments that are not exposed to severe corrosion and has good adhesion even on surfaces cleaned with hand tools. Its uses include:
- Pipelines outside and exposed to air
- Marine equipment
- Oil, Gas and Petrochemical Industries
- Structures and steel structures
Technical specifications
| فام | ocher red |
| Volume solid percentage | 71 ± 2 |
| Recommended thickness | 40 to 70 microns |
| Density | 05, 0 ± 0.55 |
| Theoretical coverage of 70 microns per kilogram | 6.6 square meters |
| Theoretical coverage of 70 microns per liter | 10.2 square meters |
| Number of components | single component |
Drying and coating conditions
| Drying time | Next layer application time | ||||||
| Temperature | surface | depth | Complete hardening | minimum | Maximum | Notes | |
| 25 ° C | 6 hours | 26 hrs | 7 days | 48 hours | 5 days | Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time. | |
Terms and equipment of application
| Thinner | Alkyd Thinner |
| Storage time | one year |
| Application temperature | 5 to 50 degrees Celsius |
| Maximum relative humidity | 80% |
| Surface temperature | 3 to 5 degrees above the dew point |
| Application method | Air spray. Airless spray, brush and roll |
| Application conditions | Ordinary spray | Airless spray | brush | Roll |
| Percent solvent | 15-20% | 5 to 98% | 10-7% | 4-6% |
| head pressure | 4 to 6 times | 120 – 160 bar | ||
| Nozzle head diameter | 1.6 to 2 mm | 0.25 to 0.55 mm | ||
| hand distance | 30-50 cm | 40-60 cm |
Surface preparation
Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting, the surface should be completely dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface with a suitable solvent to remove grease, salt and any other contaminants. De-rust and create profiles on surfaces by various methods such as sand blasting up to 2.5 degrees Swedish or by mechanical tools up to ISO-ST3 degree. In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating a profile, remove the particles from the preparation and other contaminants from the surface with a pressure of air free of moisture and grease and with the method of vacuum and thoroughly clean. Note that the application of the first layer (primer) should be done no later than two hours after preparation.
Concrete surfaces – If the concrete is fresh, it must be 28 days after the concrete has been applied (the concrete surface is completely dry). If the concrete is old, the surface must be washed with fresh water to remove contaminants such as salts, grease, dust and Dust, loose and unstable particles, etc. should be removed from its surface. If necessary, especially in the case of old concretes, it is recommended to use alkaline degreasers to remove all contaminants and to repeat the washing operation with water after degreasing. The mechanical method is created by the mechanical power tool suitable roughness on the surface and finally by normal air pressure of moisture and fat or by the method of vacuum
محصولات مشابه
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.