Description of nano traffic color

Its properties include:

1. Very smooth, even and impermeable surface
2. Very good brightness and effect
3. Good abrasion resistance
4. Water and moisture resistant
5. Excellent resistance to ultraviolet radiation of the sun
6. Oils resistant to fuels
7. Very fast drying speed
8. has very good self-cleaning capability
9. Excellent adhesion to asphalt and concrete
10. Excellent adhesion and durability
11. Can be used and executed with marking machines
12. Usability in different climatic zones
13. Can be used with glass bits

---

Uses

This color is widely used for marking and marking roads and passages, including its uses are:

• Roads and highways
• Airport runway markings
• Urban thoroughfares
• Urban bookmarks
• Marking halls and parking lots
• Painting floors and walls of halls and parking lots

---

Technical specifications

---

Drying and coating conditions

---

Terms and equipment of application

---

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree (SP10-SSPC). In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.

---

Staining instructions

After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform. Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.

---

Storage and transportation

The above color was flammable

Description of key syringe liner (IPS-M-TP-115)

Its properties include:

1. Good abrasion resistance
2. Water and moisture resistance
3. Resistance to oils, chemicals and petroleum products
4. Easy and fast implementation
5. Excellent adhesion to concrete and masonry and metal surfaces
6. Proper corrosion resistance

---

Uses

This ester is used as a primer layer for systems with medium and good capability in terms of corrosion and achieves special capabilities due to its price and ease of use. Among its uses are:

• Marine Industries
• Pipelines and steel and concrete structures
• Gas and oil pipes
• Refineries, power plants and chemical plants
• Drilling equipment

---

Technical specifications

---

Drying and coating conditions

---

Terms and equipment of application

---

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting, the surface should be completely dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface with a suitable solvent to remove grease, salt and any other contaminants. De-rust and create profiles on surfaces by various methods such as sand blasting up to 2.5 degrees Swedish or by mechanical tools up to ISO-ST3 degree. In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove them from the surface with a vacuum method free of moisture and grease and by vacuum method and thoroughly clean them. Note that the application of the first layer (primer) should be done no later than two hours after preparation. Concrete surfaces – If the concrete is fresh, it must be 28 days after the concrete has been applied (the concrete surface is completely dry). If the concrete is old, the surface must be washed with fresh water to remove contaminants such as salts, grease, dust and Dust, loose and unstable particles, etc. should be removed from its surface. If necessary, especially in the case of old concretes, it is recommended to use alkaline degreasers to remove all contaminants and to repeat the washing operation with water after degreasing. The mechanical method is created by a suitable roughness mechanical tool on the surface and finally by normal air pressure from moisture and grease or by vacuum the surface is removed from all the particles left and but