Zinc alkyd phosphate primer

Alkaline zinc phosphate primer as an anti-corrosion primer is widely used for metal structures, which is due to the presence of anti-corrosion pigment zinc phosphate in this paint, which has made the surfaces resistant to atmospheric factors and moisture. This primer is usually applied with a brush on the work surface, which causes better penetration into the pores of the surface and creates good adhesion and resistance against corrosive agents. Also in cases where the metal surface is not completely clean. Using a brush creates better adhesion. This primer is usually applied as a first or middle layer on a suitable primer. This primer is more used than lead oxide (syringe) primer, especially in environments where sulfur dioxide is present.

Description of nano traffic color

Its properties include:

Very smooth, even and impermeable surface
Very good brightness and effect
Good abrasion resistance
Water and moisture resistant
Excellent resistance to ultraviolet radiation of the sun
Oils resistant to fuels
Very fast drying speed
has very good self-cleaning capability
Excellent adhesion to asphalt and concrete
Excellent adhesion and durability
Can be used and executed with marking machines
Usability in different climatic zones
Can be used with glass bits

Uses

This color is widely used for marking and marking roads and passages, including its uses are:

Roads and highways
Airport runway markings
Urban thoroughfares
Urban bookmarks
Marking halls and parking lots
Painting floors and walls of halls and parking lots

Technical specifications

فام td>	Traffic white – Traffic yellow – Other shades
Volume solid percentage	58 ± 2
Storage time	one year
Recommended thickness	100 to 400 microns
Density	05, 0 ± 1.25
350 micron theory coverage	1.2 square meters per kilogram

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
25 ° C	1 hour	10 hours	2 days	6 hours	7 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Traffic thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	5-10%	3-5%	3-7%	4-8%
head pressure	2 -5 times	140 – 160 bar
Nozzle head diameter	1.2 to 1.8 mm	0.3 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree (SP10-SSPC). In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.

Staining instructions

After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform. Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.

Storage and transportation

The above color was flammable

Description of zinc alkyd phosphate primer

Its properties include:

Good abrasion resistance
Water and moisture resistant
Resistance to oils, chemicals and petroleum products
Easy and fast implementation
Excellent adhesion to concrete and masonry and metal surfaces
Proper corrosion resistance

Uses

This primer is used to protect steel structures against corrosive agents in marine or urban industrial environments and has good adhesion even on surfaces cleaned with hand tools. It should be noted that this liner is not suitable for protecting structures immersed in water. Its uses include:

Structures and metal construction parts
Pipelines and steel structures
Gas and oil pipes
Industrial equipment

Technical specifications

فام td>	ocher red – brown
Volume solid percentage	60 ± 2
Storage time	one year
Recommended thickness	50 to 100 microns
Density	05, 0 ± 1.55
70 micron theory coverage	5.1 square meters per kilogram
Thinner type	Alkyd Thinner
Number of components	single component

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
25 ° C	4 hours	2 days	6 days	12 hours	7 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Alkyd Thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
mixing ratio	90 by 10
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	7-10%	3-5%	5-7%	4-6%
head pressure	2 -5 times	140 – 160 bar
Nozzle head diameter	1.2 to 1.8 mm	0.3 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting, the surface should be completely dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface with a suitable solvent to remove grease, salt and any other contaminants. De-rust and create profiles on surfaces by various methods such as sand blasting up to 2.5 degrees Swedish or by mechanical tools up to ISO-ST3 degree. In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating a profile, remove the particles from the preparation and other contaminants from the surface with a pressure of air free of moisture and grease and with the method of vacuum and thoroughly clean. Note that the application of the first layer (primer) should be done no later than two hours after preparation. Concrete surfaces – If the concrete is fresh, it must be 28 days after the concrete has been applied (the concrete surface is completely dry). If the concrete is old, the surface must be washed with fresh water to remove contaminants such as salts, grease, dust and Dust, loose and unstable particles, etc. should be removed from its surface. It is recommended to use alkaline degreasers if necessary, especially in the case of old concretes, to remove all contaminants and to repeat the washing operation with water after degreasing.

محصولات مشابه

عنوان

لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.