Polyurethane surface paint (IPS – M – TP-235)

Polyurethane surface paint (IPS - M - TP-235)

Polyurethane surface paint is a two-component paint and is composed of polyurethane resin based on aliphatic isocyanate. This paint conforms to the IPS-M-TP-235 standard. The mechanism of hardening is the reaction between the components

Description of solvent-free sanitary epoxy primer

Its properties include:

Very good corrosion resistance
High chemical resistance
High abrasion resistance and hardness
Excellent water and moisture resistance
Good adhesion to steel surfaces
Applicable with thicknesses over 200 microns
Surface impermeability
Designed for health systems
Shine and excellent appearance

Uses

This coating is used alone as the final layer of sanitary epoxy systems and drinking water to protect the surfaces against corrosion and microbes. Due to the high solid percentage of paint with a spraying step, thicknesses up to 500 microns can be achieved. Its uses include:

Drinking water tanks
Water transfer pipes
Sanitary equipment
Industrial Drug Making Machines
Food Equipment
Food storage cells
Sanitary ware containers
Clean hall and operating room flooring

Technical specifications

فام td>	White (other shades suggested subject to conditions)
Volume solid percentage	100
Storage time	one year
Recommended thickness	500 to 200 microns
Density	05, 0 ± 1.53
50 micron theory cover	1.5 square meters per kilogram
Theoretical coverage of 100 microns per liter	6 m2 / td>

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	practical	Complete hardening	minimum	Maximum	Notes
25 ° C	4 hours	24 hours	7 days	12 to 24 hours	6 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	TEP (Epoxy Thinner)
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll
useful life of paint and hardener mixture	1 hour at 20 ° C

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	15-10%	8-5%	9-6%	9-6%
head pressure	4-6 times	120-160 times
Nozzle head diameter	1.6 to 1.8 mm	0.35 to 0.5 mm
hand distance	30-50%	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting, the surface should be completely dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface with a suitable solvent to remove grease, salt and any other contaminants. De-rust and create profiles on surfaces by various methods such as sand blasting up to 2.5 degrees Swedish or by mechanical tools up to ISO-ST3 degree. In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating a profile, remove the particles from the preparation and other contaminants from the surface with a pressure of air free of moisture and grease and with the method of vacuum and thoroughly clean. Note that the application of the first layer (primer) should be done no later than two hours after preparation. Concrete surfaces – If the concrete is fresh, it must be 28 days after the concrete has been applied (the concrete surface is completely dry). If the concrete is old, the surface must be washed with fresh water to remove contaminants such as salts, grease, dust and Dust, loose and unstable particles, etc. from its surface

Description of polyamine epoxy surface paint

Its properties include: High flexibility

Shine and excellent appearance
Ability to apply up to zero degrees
Resistance to temperatures below 35 degrees below zero
Good adhesion to metal surfaces (aluminum – steel – galvanized – stainless steel and other metals)
Excellent resistance to ultraviolet radiation
Resistance to oils, chemicals and petroleum products
Good adhesion on polymer and plastic surfaces

Uses

This coating is used alone or as a surface paint for epoxy or polyurethane systems in industrial, chemical and marine environments. This coating is applied on exterior surfaces and on epoxies and compensates for their weakness against light. Its uses include:

Industrial devices and equipment
Pipelines outside and exposed to air
Coastal and offshore metal structures and installations
Refineries, power plants and chemical plants

Technical specifications

فام td>	White – different shades
Volume solid percentage	54 ± 2
Storage time	one year
Recommended thickness	50 to 70 microns
Density	05, 0 ± 1.35
Theoretical coverage of 50 microns per kilogram	8 square meters
Theoretical coverage of 50 microns per liter	11.3 m2
percentage by weight	73 ± 1
Number of components	Two components
weight ratio of components	90% of the first component and 10% of the second component (hardener)
Volume mixing ratio of components	85% of the first component and 15% of the second component (hardener)

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
25 ° C	3 hours	24 hours	7 days	24 hours	7 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Polyurethane Thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll
useful life of paint and hardener mixture	5 hours at 20 ° C

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	7-10%	3-5%	9-6%	9-6%
head pressure	2-5 times	120-160 times
Nozzle head diameter	1.2 to 1.8 mm	2 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface. Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create Profiles on surfaces by various methods such as ballast document up to 2.5 SA Swedish or by mechanical tools up to ST3-ISO (SP10-SSPC). In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer)

محصولات مشابه

عنوان

لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.