Ethyl ethyl silicate ester (IPS-M-TP-210)
The product of ethyl silicate zinc primer is a two-component primer of zinc ethyl silicate, including ethyl silicate and round zinc. The primer conforms to the standard (IS-M-TP-210). The pigment used in this primer is zinc powder, which protects the metal surface against corrosion through cathodic. It is dried by the reaction between the two components and must have enough moisture to harden the environment.
[print_button_en]
Description of nano traffic color
Its properties include:
- Very smooth, even and impermeable surface
- Very good brightness and effect
- Good abrasion resistance
- Water and moisture resistant
- Excellent resistance to ultraviolet radiation of the sun
- Oils resistant to fuels
- Very fast drying speed
- has very good self-cleaning capability
- Excellent adhesion to asphalt and concrete
- Excellent adhesion and durability
- Can be used and executed with marking machines
- Usability in different climatic zones
- Can be used with glass bits
Uses
This color is widely used for marking and marking roads and passages, including its uses are:
- Roads and highways
- Airport runway markings
- Urban thoroughfares
- Urban bookmarks
- Marking halls and parking lots
- Painting floors and walls of halls and parking lots
Technical specifications
فام td> | Traffic white – Traffic yellow – Other shades |
Volume solid percentage | 58 ± 2 |
Storage time | one year |
Recommended thickness | 100 to 400 microns |
Density | 05, 0 ± 1.25 |
350 micron theory coverage | 1.2 square meters per kilogram |
Drying and coating conditions
Drying time | Next layer application time | ||||||
Temperature | surface | depth | Complete hardening | minimum | Maximum | Notes | |
25 ° C | 1 hour | 10 hours | 2 days | 6 hours | 7 days | Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time. |
Terms and equipment of application
Thinner | Traffic thinner |
Application temperature | 5 to 50 degrees Celsius |
Maximum relative humidity | 80% |
Surface temperature | 3 to 5 degrees above the dew point |
Application method | Air spray. Airless spray, brush and roll |
Application conditions | Ordinary spray | Airless spray | brush | Roll |
Percent solvent | 5-10% | 3-5% | 3-7% | 4-8% |
head pressure | 2 -5 times | 140 – 160 bar | ||
Nozzle head diameter | 1.2 to 1.8 mm | 0.3 to 0.5 mm | ||
hand distance | 30-50 cm | 40-60 cm |
Surface preparation
Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect
Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create
Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree
(SP10-SSPC).
In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness.
After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.
Staining instructions
After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform.
Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.
Storage and transportation
The above color was flammable
Description of Zinc Ethyl Silicate (IPS-M-TP-210)
Its properties include:
- Excellent resistance to solvents
- Excellent anti-corrosion and protective properties
- Good resistance to soaping
- Abrasion resistance and good impact resistance
- Excellent resistance to continuous heat up to 400 ° C
- Excellent resistance to chemicals in the pH range between 6-9
- Excellent moisture resistance
- Quick drying
Uses
This coating is used as a primer in a coating system on metal to protect against corrosion. Due to cathodic protection, this primer can be used in various highly corrosive industrial and marine conditions. Also, this primer can be used in wet and non-chemical areas as a single layer (at least 6 months). Other uses for this primer include:
- Drilling rigs
- Covering pipes and tanks
- Refineries, power plants and chemical plants
- Metal equipment and structures in industrial environments
- Heat resistant systems up to 400 ° C
- Primer in fire protection systems
- Marine systems
- Oil, Gas and Petrochemical Industries
Technical specifications
فام td> | gray |
Percentage of round zinc in dry film | at least 75% |
Volume solid percentage | 65 ± 2 |
Storage time | 6 months at 25 ° C |
Recommended thickness | 65 microns |
Density | 1/0 ± 5/2 |
Theoretical coating with a thickness of 70 microns | 3.5 square meters per kilogram |
Theoretical coating with a thickness of 70 microns | 8.8 square meters per liter |
Number of components | Two components |
weight ratio of components | 75% of the first component 25% of the second component (hardener) |
Volume mixing ratio of components | 68% of the first component and 32% of the second component (hardener) |
Drying and coating conditions
Drying time | Next layer application time | ||||||
Temperature | surface | practical | Complete hardening | minimum | Maximum | Notes | |
25 ° C | 20 minutes | 2 hours | 5 days humidity 70-5% | 6 days | Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time. |
Terms and equipment of application
Thinner | Thinner ethyl silicate |
Application temperature | 5 to 50 degrees Celsius |
Maximum relative humidity | 80% |
mixing ratio | 80 to 20 |
Surface temperature | 3 to 5 degrees above the dew point |
Application method | Air spray. Airless spray, brush and roll |
useful life of paint and hardener mixture | 30 minutes at 20 ° C |
Application conditions | Ordinary spray | Airless spray | brush | Roll |
Percent solvent | if needed | if needed | 9-6% | 9-6% |
head pressure | 4-6 times | 120-160 times | ||
Nozzle head diameter | 1.6 to 2 mm | 0.35 to 0.5 mm | ||
hand distance | 30-50 cm | 40-60 cm |
Surface preparation
Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect
Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create
Profiles on surfaces with different methods such as ballast document up to 2.5 Swedish SA or by location tool
محصولات مشابه
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.
عنوان
لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.