Furnace acrylic varnish

Acrylic lacquer is a transparent, colorless and thermoset-based acrylic resin that has a very good resistance to yellowing. These varnishes are soluble in solvents such as primers, aromatic solvents and present and insoluble in aliphatic solvents. It also has good resistance to water and stains caused by some materials. This varnish is resistant to heat and has good resistance to chemicals such as detergents, oils and greases, as well as high abrasion resistance and hardness.

[print_button_en]

Description of nano traffic color

Its properties include:

Very smooth, even and impermeable surface
Very good brightness and effect
Good abrasion resistance
Water and moisture resistant
Excellent resistance to ultraviolet radiation of the sun
Oils resistant to fuels
Very fast drying speed
has very good self-cleaning capability
Excellent adhesion to asphalt and concrete
Excellent adhesion and durability
Can be used and executed with marking machines
Usability in different climatic zones
Can be used with glass bits

Uses

This color is widely used for marking and marking roads and passages, including its uses are:

Roads and highways
Airport runway markings
Urban thoroughfares
Urban bookmarks
Marking halls and parking lots
Painting floors and walls of halls and parking lots

Technical specifications

فام	Traffic white – Traffic yellow – Other shades
Volume solid percentage	58 ± 2
Storage time	one year
Recommended thickness	100 to 400 microns
Density	05, 0 ± 1.25
350 micron theory coverage	1.2 square meters per kilogram

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
25 ° C	1 hour	10 hours	2 days	6 hours	7 days	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Traffic thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	5-10%	3-5%	3-7%	4-8%
head pressure	2 -5 times	140 – 160 bar
Nozzle head diameter	1.2 to 1.8 mm	0.3 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting the surface must be perfect
Dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface thoroughly to remove grease, salt and any other contaminants. De-ring and create
Profiles on surfaces by various methods such as ballast document up to 2.5 degrees Swedish SA or by mechanical tools up to ST3-ISO degree
(SP10-SSPC).
In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness.
After de-rusting and creating the profile of the particles obtained from the preparation and other contaminants, remove the surface with moisture and grease free from moisture and grease by vacuum method. Note that the application of the first layer (primer) should be done no later than two hours after preparation.

Staining instructions

After preparing the surface and choosing the method of painting, first mix the fabric of the relevant solution with the recommended ratio and mix the mixture thoroughly to make it uniform.
Add a special amount of ethyl silicate thinner if needed (usually not needed) (add to the mixture and stir until a primer is applied, then apply the paint with a suitable tool.

Storage and transportation

The above color was flammable

Description of acrylic lacquer furnace

Its properties include:

Suitable abrasion resistance
Ability to apply up to zero degrees
Water and moisture resistance
Excellent resistance to ultraviolet radiation
Resistance to oils and chemicals
Shine and great effect
Good thermal resistance
Excellent adhesion to metal surfaces
Good adhesion to galvanized and aluminum

Uses

This varnish is used to enhance and improve the beauty and gloss of the work surface and protect the surface. This varnish has good adhesion on aluminum, brass and iron surfaces or is used as a gloss coating on some colors, especially metallic paint. This varnish is also used in the automotive, bicycle and motorcycle industries. Its uses include:

Metal Industries
Automotive Industries
Decorative industries

Technical specifications

فام	Colorless
Volume solid percentage	40 ± 2
Storage time	one year
Recommended thickness	50 to 100 microns
Density	05, 0 ± 1
mixing ratio	2 in 1
50 micron theory cover	8 square meters per kilogram

Drying and coating conditions

Drying time				Next layer application time
Temperature	surface	depth	Complete hardening	minimum	Maximum	Notes
150 ° C			20 minutes in the oven	After hardening	Unlimited	Other factors such as the thickness of the color film and temperature changes, etc. affect the drying time.

Terms and equipment of application

Thinner	Furnace acrylic thinner
Application temperature	5 to 50 degrees Celsius
Maximum relative humidity	80%
Surface temperature	3 to 5 degrees above the dew point
Application method	Air spray. Airless spray, brush and roll

Application conditions	Ordinary spray	Airless spray	brush	Roll
Percent solvent	7-10%	3-5%	5-7%	4-6%
head pressure	2 -5 times	140 – 160 bar
Nozzle head diameter	1.2 to 1.8 mm	0.3 to 0.5 mm
hand distance	30-50 cm	40-60 cm

Surface preparation

Painted surfaces – These surfaces must be completely clean and free of any grease and other contaminants. Before painting, the surface should be completely dry and if a long time has passed since the application of the undercoat, a suitable roughness should be created by soft sanding on the surface.
Steel surfaces – Wash the steel surface with a suitable solvent to remove grease, salt and any other contaminants. De-rust and create profiles on surfaces by various methods such as sand blasting up to 2.5 degrees Swedish or by mechanical tools up to ISO-ST3 degree. In metal structures and welded points and corners should be smooth and polished and free of any appendages and sharpness. After de-rusting and creating a profile, remove the particles from the preparation and other contaminants from the surface with a pressure of air free of moisture and grease and with the method of vacuum and thoroughly clean. Note that the application of the first layer (primer) should be done no later than two hours after preparation.
Concrete surfaces – If the concrete is fresh, it must be 28 days after the concrete has been applied (the concrete surface is completely dry). If the concrete is old, the surface must be washed with fresh water to remove contaminants such as salts, grease, dust and Dust, loose and unstable particles, etc. should be removed from its surface. It is recommended to use alkaline degreasers to remove all contaminants if necessary, especially in the case of old concretes, and to repeat the washing operation with water after degreasing. Mechanical method powe mechanical tool

محصولات مشابه

عنوان

لورم ایپسوم متن ساختگی با تولید سادگی نامفهوم از صنعت چاپ و با استفاده از طراحان گرافیک است. چاپگرها و متون بلکه روزنامه و مجله در ستون و سطر آنچنان که لازم است.